1. Running procedures of floating fish feed device
( 1) Safety measures before beginning and after stopping
① Inspect all parts of fish feed drifting pellet making machine, especially the connecting screws and also support screws of each section of the puffing chamber, the linking screws between the motor base and also the framework, and also the screw connection between the puffing chamber and also the framework, as well as there must be no looseness;
② Manually turn the primary shaft, right now, there need to be no rubbing sound in the fish feed drifting pellet making equipment puffing cavity;
③ Start the feeding auger of fish feed floating pellet making device, examine its stepless high-speed efficiency, and also call for typical operation;
Related post: fish feed mill plant
④ Inspect and cleanse the water as well as gas courses before beginning the fish feed drifting pellet making machine, and all filters require to be cleansed;
⑤ Prior to starting the fish feed floating pellet making device, inspect whether the circuitry of the electrical control part is proper, whether the rotation of each motor is appropriate, as well as whether the control is trustworthy;
⑥ After the fish feed drifting pellet making maker is stopped, you should use high-temperature handwear covers, promptly get rid of the discharge mold, and also promptly tidy it while it is warm, and start the major motor to empty the product built up in the puffing dental caries. When the corn is blown, soybean powder ought to be added The product is rinsed tidy;
⑦ Pay attention to safety and security when dumping the device, as well as do not stand in front of the equipment to prevent threat brought on by recurring stress in the fish feed floating pellet making maker cavity;
⑧ After the fish feed drifting pellet making device is running typically, it shall not be closed down at will.
Related post: https://www.richipelletmachine.com/fish-feed-mill-plant/
( 2) Power on
① Before beginning the fish feed drifting pellet making machine, examine the fasteners, as well as there need to be no looseness;
② Ensure the normal supply of steam and also water;
③ Make certain that the power supply as well as electrical appliances are normal;
④ Open up the vapor shutoff, pre-heat the floating fish pellet equipment blowing chamber, the temperature level is about 100 levels;
⑤ Start the fish feed drifting pellet making maker: begin the conditioner, start the feeding auger, when there is material spurting from the outlet of the conditioner, begin adding vapor to the conditioner.
A small amount of water is added, and the material is fed into the blowing dental caries at the same time. After the product is extruded by fish feed floating pellet making device, the puffing effect and also moisture of the item are adjusted.
( 3) Downtime
After the fish feed floating pellet making device production concerns an end, it needs to be stopped. The stop series is: feeding auger and conditioner. After that wait up until the indicated worth of the main engine current on the electric control cupboard comes to be the no-load present worth, after that quit the primary electric motor as well as the oil pump electric motor.
( When the corn is puffed, about 25 kg of soybeans must be fed right into the bypass feeding port of the initial section of the puffing tooth cavity. To clean up the recurring corn material in the puffing cavity, and then stop the main motor to avoid the fish feed drifting pellet making device from blocking), after that swiftly take apart the puffing dental caries of the tail area for cleansing.
After cleansing, apply grease to the inner wall of the major shaft as well as screw head (After feeding oil), re-install it and wait for the next boot;
When you see that the product level indicator on the silo shows that the material level has actually reached the lowest degree, begin to prepare for shutdown. At this time, do not quit the feeding auger as well as conditioner, as well as quit feeding when the primary fish feed drifting pellet making equipment existing decreases to the no-load present auger and conditioner.
Related post: poultry feed plant price
2. Procedure series of floating fish feed equipment
( 1 )When puffing soybeans, the two areas at the inlet end of the blowing cavity are single screw heads, and the 3 sections at the outlet end are furnished with double screw heads.
First, include heavy steam to the coat to preheat the blowing cavity to concerning 100 degrees, as well as put the screws on the blowing tooth cavity at the tail area. After the plug is tightened, loosen it for 3-4 turns, and then tighten up the screw plug to repair the screw plug before feeding.
By regulating the stepless high-speed device of the feeding auger, the feeding speed is from slow to fast, and also the feeding rate is from little to big. After the soybean dish is expelled from the screw plug hole, add the cover to go into the typical production, and configure the screw connects with various apertures to get soybean dish with various yields and excellences.
By configuring the conical pressure rings of various sizes, the indicated temperature level of the four-section (discharge end) puffing tooth cavity is 130-140 levels. It is suggested that the screen of the crusher used for squashing soybeans should have a diameter of 3-4.
( 2 )When extruding fine-grained feed by fish feed drifting pellet making equipment, the extruding screws in the extruding cavity are all solitary screw heads, add vapor to the coat to preheat the blowing cavity to concerning 80 levels, and also get in the fish feed drifting pellet making device and steam evenly appeased and toughened up powder. my website
Concerning 18%, this have to be carried out in the feed conditioner, and the feed amount is managed by the stepless rate managing device from tiny to large. Keep in mind that the reading of the ammeter of the primary electric motor ought to not go beyond the rated existing of the primary engine of fish feed drifting pellet making equipment.
Be careful of overloading the electric motor and also squeezing out fine-grained materials. When the temperature of the extruding chamber at the discharge end is regulated to an proper degree by setting up conelike stress rings with different sizes.
The above is the concept, framework as well as running procedures of the fish feed drifting pellet making device presented by Richi Equipment. In pursuit of crunchy taste and good appearance, producers often add a raising representative (or baking powder), which contains a particular quantity of aluminum elements, as well as creates gas when warmed throughout cooking or frying, and also the leavening agent is inside the food.
For details please contact: fish feed machine
WhatsApp:86 138 3838 9622
Email:enquiry@richipelletmachine.com
- February 2024 (3)
- January 2024 (3)
- October 2023 (3)
- August 2023 (15)
- July 2023 (9)
- June 2023 (3)
- May 2023 (12)
- April 2023 (4)
- March 2023 (6)
- February 2023 (3)
- December 2022 (6)
- November 2022 (6)
- October 2022 (5)
- August 2022 (7)
- July 2022 (2)
- June 2022 (1)
- May 2022 (5)
- April 2022 (6)
- March 2022 (1)